Search found 11 matches

by AND_1
Wed Jun 21, 2017 5:38 pm
Forum: Development
Topic: Manipulate Joystick Data
Replies: 14
Views: 327

Re: Manipulate Joystick Data

Hi Matlo, until now I made a function which builds a String that contains the Linux commands (e.g. gimx --event "rel_axis_0(32767)" --dst 127.0.0.1:51914) and when I start this c-programm it executes the String as a terminal command using the execv-funktion. It works but I have massive latency issue...
by AND_1
Fri Jun 16, 2017 12:35 pm
Forum: Development
Topic: Manipulate Joystick Data
Replies: 14
Views: 327

Re: Manipulate Joystick Data

Hi Matlo, I have a function, which generates the byte array, but now I am not sure how to send this report to GIMX. Is there a specific function from GIMX to send it? Or how I am going to do this? Or do I need to write this function? Maybe you can give me an advice how to do that and what I need to ...
by AND_1
Mon Jun 12, 2017 3:24 pm
Forum: Development
Topic: Manipulate Joystick Data
Replies: 14
Views: 327

Re: Manipulate Joystick Data

Thanks Matlo. I have a C-Funktion which prints first: The event type, afterwards the array length and finally the value of the axes. Does it work with the printf-statement, that GIMX can understand the report? Or do I need to have a send-function for the report? How can I get my bytes into the repor...
by AND_1
Mon Jun 12, 2017 1:51 pm
Forum: Development
Topic: Manipulate Joystick Data
Replies: 14
Views: 327

Re: Manipulate Joystick Data

Hi Matlo, Thanks for your answer. So I did a programm to Read Joystick data from /dev/input/js* and print it to console. Now I am wondering how to use the Network API. I don't really understand how it works and what I need to do. The IP:port arguement is what I don't get. Which adresses are meant? D...
by AND_1
Fri Jun 09, 2017 1:29 pm
Forum: Development
Topic: Manipulate Joystick Data
Replies: 14
Views: 327

Re: Manipulate Joystick Data

Hi Matlo, thanks for replying with that frequency. :) But I want to do something different. I could send you a png-file of my project. I want to catch the data while GIMX is running and send them with CAN to another device, where these datas will be modified. So I need the data coming from the G27 w...
by AND_1
Wed Jun 07, 2017 3:45 pm
Forum: Development
Topic: Manipulate Joystick Data
Replies: 14
Views: 327

Re: Manipulate Joystick Data

Thanks for your fast replies. But I think there is a missunderstanding. I want to catch the data while GIMX is running and modify them before they were send over the USB-Adapter. So I want to catch the data from the G27, modify them and then send the new data using your USB-Adapter. So that there ar...
by AND_1
Wed Jun 07, 2017 2:48 pm
Forum: Development
Topic: Manipulate Joystick Data
Replies: 14
Views: 327

Re: Manipulate Joystick Data

Hi Matlo, I am using a G27 Wheel (Original Gaming Wheel) which is stucked in a Raspberry Pi3 USB Port. Then I connect my laptop with the Raspberry using your USB-Adapter. GIMX is running on the PI. So I suppose that the Signal of my G27 is going through the Raspberry into my laptop. Because I was ab...
by AND_1
Wed Jun 07, 2017 1:26 pm
Forum: Development
Topic: Manipulate Joystick Data
Replies: 14
Views: 327

Manipulate Joystick Data

Hello Guys, I have a question about the Sourcecode, because it is a huge amount of Source Code in GIMX ;) I want to manipulate the values of my G27 Wheel. So I need to get the values before they are going to be send over the USB-Adapter. But I am quite clueless where to start in the Sourcecode. In w...
by AND_1
Wed May 31, 2017 11:05 am
Forum: General Discussion
Topic: Car racing simulator
Replies: 5
Views: 1574

Re: Car racing simulator

Hi Guys, I see that this post is a few time ago ;) but I am at the same point in a project. I want to use a Beaglebone Black as a device for my PC (Host) that emulates the G27 Wheel and get the data from an Original G27 Wheel on my Beaglebone via On-board USB-Host port. Can I get the data through th...
by AND_1
Wed May 31, 2017 8:47 am
Forum: Support
Topic: No config was found in GIMX-Launcher
Replies: 1
Views: 85

No config was found in GIMX-Launcher

Hello everyone, 1. I bought an USB-Adapter from the official GIMX-Shop, my PC sees it as "Silicon Labs Cp210x USB to UART Bridge (COM12)". I ordered it with the EMUG27PC Package, but if I connect it, it isn't called G27 Steering Wheel. And also the Logitech Profiler doesn't identify it. I plugged it...