Search found 12 matches

by Pr2
Sun Apr 08, 2018 8:54 pm
Forum: GIMX Discussion
Topic: Adapt TH8 gearshift
Replies: 3
Views: 331

Re: Adapt TH8 gearshift

Matlo wrote:
Sun Apr 08, 2018 7:15 pm
Hi,

gimx-config is the appropriate tool for this task.
Hi matlo

The problem here is that i cannot run gimx-config from terminal. Could i run the tool on other computer and produce a valid config for my rpi3?
by Pr2
Sun Apr 08, 2018 3:02 pm
Forum: GIMX Discussion
Topic: Adapt TH8 gearshift
Replies: 3
Views: 331

Adapt TH8 gearshift

Hi everyone. I want to know if there is any option for adapt a thrustmaster gearbox in addition to g27-g29 wheel. I have seen the config file so i suppose i can edit this file in order to "say" the buttons pressed on mi th8 are the 1st gear, 2nd gear, etc... Is there any tutorialbor similar that cou...
by Pr2
Sun Apr 01, 2018 8:43 pm
Forum: GIMX Discussion
Topic: ERROR: FAILED TO READ PACKET HEADER FROM THE GIMX ADAPTER
Replies: 2
Views: 648

ERROR: FAILED TO READ PACKET HEADER FROM THE GIMX ADAPTER

HI Im trying to setup a DYI adapter using raspberry pi and arduino pro micro. I have intalled GIMX 7.2 to do so The problem is that when I try to start GIMX, I allways get the following error: ERROR: FAILED TO READ PACKET HEADER FROM THE GIMX ADAPTER I have flashed my AVR board again, checked the wi...
by Pr2
Sun Apr 01, 2018 8:38 pm
Forum: GIMX Discussion
Topic: SHUTDOWN USING DIETPI - ONBOARD UART
Replies: 5
Views: 442

Re: SHUTDOWN USING DIETPI - ONBOARD UART

I have finally found the answer to shutdowns. My wiring was incorrect. I have a new problem but I will open a new thread to explain that
by Pr2
Fri Mar 30, 2018 8:14 pm
Forum: GIMX Discussion
Topic: SHUTDOWN USING DIETPI - ONBOARD UART
Replies: 5
Views: 442

Re: SHUTDOWN USING DIETPI - ONBOARD UART

Yes it definetly corerct. Im thinking that maybe my firmware is not correctly loaded. I have loaded the EMUG29PS4/atmega32u4.hex, maybe is needed other firmware? Other odd thing is that when i plug in pro micro only the green led is on, if I reset the board then 2 red leds are switched on as well as...
by Pr2
Thu Mar 29, 2018 10:24 pm
Forum: GIMX Discussion
Topic: SHUTDOWN USING DIETPI - ONBOARD UART
Replies: 5
Views: 442

Re: SHUTDOWN USING DIETPI - ONBOARD UART

Yes, i placed the two resistors in order to divide voltage
by Pr2
Thu Mar 29, 2018 10:04 am
Forum: GIMX Discussion
Topic: SHUTDOWN USING DIETPI - ONBOARD UART
Replies: 5
Views: 442

SHUTDOWN USING DIETPI - ONBOARD UART

Hello everyone Im trying to connect G27 emulating G29. My setup is RPI3 + arduino pro micro, using onboard uart. Also, i have downladed DIETPI premade image. My problem is that Dietpi shutdowns itself and i dont know why. It happens (i think) when RPI3 is connected with arduino, and oddly, happens e...
by Pr2
Mon Mar 26, 2018 6:07 pm
Forum: GIMX Discussion
Topic: G27 - RPI3 - ARDUINO PRO MICRO
Replies: 0
Views: 1163

G27 - RPI3 - ARDUINO PRO MICRO

Hi! Im trying to build a DIY adapter using RPI3, arduino pro micro and a g27. No USB to TTL device, as CP2102 is planned to be included in my setup. I've correctly burned the image onto RPI3, my problem becomes on uploading firmware on arduino pro micro. Every time I try to upload atmega32u4.hex fir...
by Pr2
Mon Mar 26, 2018 5:57 pm
Forum: GIMX Discussion
Topic: [Tutorial] Logitech G27 (and other wheels) on PS4 using Pi
Replies: 47
Views: 39432

Re: [Tutorial] Logitech G27 (and other wheels) on PS4 using Pi

Hello! I cannot understand how you have connected a teensy without using CP2102 or other USB to UART interface! Could you please clear this out?? Thx, im trying to do the same but using arduino micro.
by Pr2
Sun Feb 11, 2018 11:58 am
Forum: GIMX Discussion
Topic: Is USB to UART needed on RPi?
Replies: 2
Views: 400

Re: Is USB to UART needed on RPi?

Thx Matlo

Sorry for post on the wrong section!