Search found 206 matches

by LoneWolf81
Wed Nov 25, 2020 8:49 am
Forum: Support
Topic: RPi Installation Error
Replies: 2
Views: 41

Re: RPi Installation Error

Hi run these commands you can replace the name of the .deb life if you want to install 7.15

Code: Select all

sudo dpkg --force-overwrite -i gimx_8.0-1_armhf.deb

Code: Select all

sudo apt-get install -f
by LoneWolf81
Tue Nov 24, 2020 4:31 am
Forum: Support
Topic: firmware loading problems
Replies: 2
Views: 64

Re: firmware loading problems

Hi

From the log file it seems you are not pressing the button mapped to PS you can also disregard the error message as its not a fatal error.
by LoneWolf81
Mon Nov 16, 2020 2:03 pm
Forum: GIMX Discussion
Topic: Will GIMX work on PS5?
Replies: 19
Views: 1225

Re: Will GIMX work on PS5?

@mascherano

This is actually a discussion on the PS5 compatibility, as for your question the team is still working on wheel emulation for the Xbox one and there is no ETA at the moment.
by LoneWolf81
Sat Nov 14, 2020 6:15 pm
Forum: Support
Topic: firmware loading problems
Replies: 13
Views: 651

Re: firmware loading problems

Im not sure if the force feedback can be adjusted as I dont have a wheel to set it up with.

If you load the EMUPS4.hex you can emulate a Dualshock 4 and use any method of input that can be detected by the computer
by LoneWolf81
Sat Nov 14, 2020 10:21 am
Forum: Support
Topic: firmware loading problems
Replies: 13
Views: 651

Re: firmware loading problems

You have the wrong firmware loaded you have to load the EMUG29PS4.hex the one you currently have loaded is for the PS2

The PS4 needs to be on and your Dualshock 4 off
by LoneWolf81
Fri Nov 13, 2020 5:27 pm
Forum: Support
Topic: firmware loading problems
Replies: 13
Views: 651

Re: firmware loading problems

Set the messages to log file and paste it on pastebin then link it here
by LoneWolf81
Thu Nov 12, 2020 2:39 pm
Forum: GIMX Discussion
Topic: Xbox Series X
Replies: 9
Views: 519

Re: Xbox Series X

It should work unless they require an update to the controller firmware for it to work on the X/S series. I will definitely be holding thumbs for you if you are in a position to test it and looking forward to your feedback :)
by LoneWolf81
Thu Nov 12, 2020 1:46 pm
Forum: GIMX Discussion
Topic: Xbox Series X
Replies: 9
Views: 519

Re: Xbox Series X

Hi In theory it should work but we wont know until someone does a test. It will all depend if they did something with the controller authentication as newer firmware updates caused GIMX to stop working when you get to the point where you have to press the guide button. Just don't update the controll...
by LoneWolf81
Wed Nov 11, 2020 3:38 am
Forum: Support
Topic: firmware loading problems
Replies: 13
Views: 651

Re: firmware loading problems

With your config selected click on file and then edit fps config press F1 or any other key you want to map to it and save the changes. Then Start GiMX and press the mapped key I have attached an image marking the key you have to map. On the Driving Force config button 8 is mapped to PS if you look a...
by LoneWolf81
Tue Nov 10, 2020 5:13 pm
Forum: Support
Topic: firmware loading problems
Replies: 13
Views: 651

Re: firmware loading problems

As for your previous question with the GND pin not connected the AVR would not reset so it will fail to detect. If you connected the uart side it will still show the dos screen but fail to program. In your config you need to bind a button for PS you can do this by going to the config editor and assi...