Game Input MultipleXer

Log will be under /root/.gimx/log directory
To enable log use -l logFileName.log parameter

Pay attention that the log file will be overwritten if gimx restarts

Alright I will try get the log file over lunch. The only issue is I don't think its really going to show anything because everything works fine its just missing the tension. My steering wheel calibrates the instant I power the pi on and it only does it once. Once the pi has booted I have a button I press that starts gimx my steering wheel does not recalibrate when I press this button. I press the button gimx starts and everything works. Just to restate my wheel only calibrate once and that is right when the pi gets power.

This is the same for me. It is normal, the wheel start calibration when you connect the usb

Are you using the Logitech force gt steering wheel and does your wheel have tension right away?

global option -l with value `log.txt'
GIMX 5.8 ARMv6
Raspbian GNU/Linux 8.0 (jessie)
Linux 4.4.15-v7+ #897 SMP Tue Jul 12 18:42:55 BST 2016 unknown
Bus 001 Device 006: ID 046d:c29a Logitech, Inc.
Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp. SMSC9512/9514 Fast Ethernet Adapter
Bus 001 Device 002: ID 0424:9514 Standard Microsystems Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
cannot get USB device tree
native mode is already enabled for HID device 01:01:02 (PID=c29a)
Detected USB adapter: G29 PS4.
No controller was found on USB buses.
adapter_detect failed


THis was the log file which is weird because my steering wheel worked???

No controller was found on USB buses.
adapter_detect failed

No good.

Connect original console controller to you rpi and usb-serial converter

global option -l with value `log2.txt'
GIMX 5.8 ARMv6
Raspbian GNU/Linux 8.0 (jessie)
Linux 4.4.15-v7+ #897 SMP Tue Jul 12 18:42:55 BST 2016 unknown
Bus 001 Device 006: ID 046d:c29a Logitech, Inc.
Bus 001 Device 005: ID 054c:05c4 Sony Corp.
Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp. SMSC9512/9514 Fast Ethernet Adapter
Bus 001 Device 002: ID 0424:9514 Standard Microsystems Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=dwc_otg/1p, 480M
|__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/5p, 480M
|__ Port 1: Dev 3, If 0, Class=Vendor Specific Class, Driver=smsc95xx, 480M
|__ Port 2: Dev 5, If 0, Class=Human Interface Device, Driver=usbhid, 12M
|__ Port 4: Dev 6, If 0, Class=Human Interface Device, Driver=usbhid, 12M
native mode is already enabled for HID device 01:01:04 (PID=c29a)
Detected USB adapter: G29 PS4.
using default refresh period: 5.00ms
1471629176.821093 timer fired 7 times...

Ignore that first log file I didnt realize it didnt update...

so i did downgraded my firmware via a differnt post. ANd that corrected my issues. Thank You so much!!!!

sudo rpi-update 771a503cfc2a1130e2df2a4ddfc45ffa0f592b3f

Thanks for the feedback. I added a note on the wiki page.