Page 1 of 3
G27->G29 DIY USB using Ubuntu
Posted: Fri Oct 30, 2015 9:14 pm
by Cicipso
Hi guys,
I've browsed all similar problems but couldn't find an example using Ubuntu as the operating system. So here goes my issue and hope you guys can help me! Thanks in advance!
- GIMX 5.2 i386
- Ubuntu 14.04.3 LTS (Trusty Tahr) - 32bit
- DIY USB CP2102 / Teensy 2++ (firmware 5.0 - EMUG29PS4 - at90usb1286.hex)
- Downloaded config LogitechG27_G29.xml
All connected to the 3 USB ports of my computer - G27, DS4 and the DIY USB between it and PS4
Seems like my computer can't "see" the DS4?
option -l with value `log.txt'
option -c with value `LogitechG27_G29.xml'
option -p with value `/dev/ttyUSB0'
status flag is set
subpos flag is set
force_updates flag is set
native mode is already enabled for HID device 02:02 (PID=c29b)
Detected USB adapter: G29 PS4.
No controller was found on USB buses.
adapter_detect failed
Cheers!
Re: G27->G29 DIY USB using Ubuntu
Posted: Fri Oct 30, 2015 9:24 pm
by Matlo
Hi,
What's the output of the lsusb command?
Re: G27->G29 DIY USB using Ubuntu
Posted: Fri Oct 30, 2015 9:58 pm
by Cicipso
Here is the output of lsusb command:
Bus 001 Device 002: ID 10f1:1a13 Importek
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 002: ID 10c4:ea60 Cygnal Integrated Products, Inc. CP210x UART Bridge / myAVR mySmartUSB light
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 003: ID 046d:c29b Logitech, Inc. G27 Racing Wheel
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Re: G27->G29 DIY USB using Ubuntu
Posted: Fri Oct 30, 2015 10:03 pm
by Matlo
The DS4 wasn't detected. Change the USB cable, and if it doesn't help, try another USB port.
Re: G27->G29 DIY USB using Ubuntu
Posted: Fri Oct 30, 2015 10:10 pm
by Cicipso
It was the cable indeed. I changed just before your reply and it has been detected. Will retry now.
Re: G27->G29 DIY USB using Ubuntu
Posted: Sat Oct 31, 2015 2:21 pm
by Cicipso
Ok. It worked partially (Driveclub),
Log file shows PS button, share, X, O, etc, except pedals.
I did a log file with only PS and pedals, and the result is showed in the pastebin link below.
Is this a behavior of missing configuration? (many lines without button name)
http://pastebin.com/NrmeuhNf
Re: G27->G29 DIY USB using Ubuntu
Posted: Sat Oct 31, 2015 2:28 pm
by des
I would like to add, that the same happened to me.
I was using Ubuntu 14 as live usb version without a permanent installation. Everything except the pedals seemed to work, at that time I didn't know if it was the live install, my usb adapter, that I only have a G25 or something else causing the issue. Wanted to get back to it later.
Re: G27->G29 DIY USB using Ubuntu
Posted: Sat Oct 31, 2015 5:23 pm
by Matlo
@Cicipso
Could you post the config on pastebin?
@des
Could you please open a thread for your issues?
It would be great to have G25 configs in the GIMX config repository!
Re: G27->G29 DIY USB using Ubuntu
Posted: Sat Oct 31, 2015 7:21 pm
by Cicipso
Here it is:
http://pastebin.com/HQGudM4m
I'm using the config the launcher downloaded automatically at first launch.
Hope there is something wrong with it...
Re: G27->G29 DIY USB using Ubuntu
Posted: Mon Nov 02, 2015 10:10 pm
by Matlo
I just played a bit with a DFGT on Ubuntu 14.04.03 64bit, and everything worked fine.
Did you do any calibration using jscal or jstest-gtk?