Game Input MultipleXer

Hello Matlo, I first want to say thank you for this great piece of software. I am more than happy that I was not forced to go and buy a new, very expensive wheel with my non-existent budget, very cool thing you have here.

I've been having an unfortunate issue with the mod lately however, and it is becoming very difficult and tedious to get it working so I can race with my group of sim friends on Project CARS. I've read and searched high and low for someone else having the problem I have been having and so far I have not been successful, hence this thread. So here's what happens when whatever circumstances aren't correct for proper functioning of the mod.

plug in teensy to PS4
plug CP2102 USB end into hub with wheel and a powered down controller
plug hub into computer
turn on PS4
start GIMX (happens in both 5.7 and 5.8)
wait for PS4 to say press PS button to start or whatever that "welcome" screen says
select DIY adapter, port, input, config
uncheck grab mouse
check config says: joystick not found: Driving Force GT USB (0)
Start the program and this happens:

Driver file operation error. DeviceIoControl failed (Cannot create a file when that file already exists. Error code = 183)
option -l with value `log.txt'
option -c with value `LogitechDrivingForceGT_G29.xml'
option -p with value `COM3'
grab flag is unset
status flag is set
subpos flag is set
force_updates flag is set
GIMX 5.7 x86_64
Windows 8.1 x64
Kernel version: 6.3 (9600)
native mode command sent to HID device \\?\hid#vid_046d&pid_c294&mi_00#8&1f842731&0&0000#{4d1e55b2-f16f-11cf-88cb-001111000030} (PID=c294)
Detected USB adapter: G29 PS4.
src/windows/async.c:180 CreateFile failed with error: The system cannot find the file specified.


src/windows/async.c:180 CreateFile failed with error: The system cannot find the file specified.


src/windows/async.c:180 CreateFile failed with error: The system cannot find the file specified.


src/windows/async.c:180 CreateFile failed with error: The system cannot find the file specified.


src/windows/async.c:180 CreateFile failed with error: The system cannot find the file specified.


HID device \\?\hid#vid_046d&pid_c294&mi_00#8&1f842731&0&0000#{4d1e55b2-f16f-11cf-88cb-001111000030} not found
libusb_open: Other error.
No controller was found on USB buses.
adapter_detect failed



Now the odd time, and it's frequently more odd each time, it finds everything and then runs like a champ until I've finished playing.

To sum up all the hardware info, I am using:

teensy 2.0 board with pins
CP2102 board with supplied "jumper" cables
5.4/EMUG29PS4/atmega32u4
PS4
Driving Force GT
Black stock PS4 controller that comes with the system
4 port Insignia USB hub
Project CARS

Again, this is a great piece of software, I absolutely love that I can use my old wheel with my PS4. When I have some money together I would be more than happy to donate you some as this is something that is worth more than the parts cost to get it working.

Thanks very much for this, and your help.

Hi,

You should install Logitech Gaming Software 5.10.
http://gimx.fr/wiki/index.php?title=Logitech_Wheels

I already have done unfortunately, it had been installed previous to the mod and I've since uninstalled, redownloaded, and installed again. Does it need to just be installed or do I have to map buttons in that program as well? I could try running that program before gimx to see if that helps.

Are you sure you installed the right version? (32-bit / 64-bit)
Without LGS the wheel remains in compatibility mode.
GIMX will try to enable the native mode (as seen in your log), but for some reason it fails on Windows.

After much testing, I've figured out that my computer doesn't constantly run LGS for some reason and when the adapter is plugged in it doesn't recognise the wheel as a DFGT, it's some light blue rimmed thing, DFP maybe. So my fix is to start the LGS before GIMX, but I found an issue where about 5-10 minutes in LGS causes something to stop detecting.

So here's my full "fix"

Start LGS
Start GIMX
Run GIMX
Press PS button
Close LGS

it then runs all day pretty much, only the odd time will it close on its own.

I downloaded LGS, and it register`s the inputs of the wheel, but do I just open LGS or do I have to do something in LGS before opening GIMX? Currently when following the five steps, GIMX still reports:
global option -l with value `log.txt'
global option -c with value `LogitechDrivingForceGT_G29_W10.xml'
controller #1: option -p with value `COM3'
now reading arguments for controller #2
status flag is set
subpos flag is set
force_updates flag is set
GIMX 5.9 x86_64
Windows 10 (or later) x64
Kernel version: 10.0 (14901)
native mode is already enabled for HID device \\?\hid#vid_046d&pid_c29a#6&28537822&0&0000#{4d1e55b2-f16f-11cf-88cb-001111000030} (PID=c29a)
Detected USB adapter: G29 PS4.
No controller was found on USB buses.
adapter_detect failed

Any help would be greatly appreciated.

Plug a Ds4 with a USB cable and try again.
Please also read the instructions here:
http://gimx.fr/wiki/index.php?title=Qui ... SB_adapter

Thank you for the speedy reply. I had a DS4 plugged in, but I found that I just needed to restart my computer and reinstall LGS for GIMX to get running. I appreciate the software and cannot wait to start using it.