Hi, i use atmega328p (arduino uno) and i want to simulate g29 in ps4 with a DFGT. Flash the arduino uno with firmware g29 atmega32u4 (can be this the problem?). Config seems ok but the log is this:
windows/gprio.c:23 gprio: failed to set priority class
global option -c with value `LogitechDrivingForceGT_G29.xml'
controller #1: option -p with value `COM4'
now reading arguments for controller #2
subpos flag is set
force_updates flag is set
../common/windows/async.c:344 async_read_timeout: ReadFile failed: timeout expired.
can't read packet header
../common/windows/async.c:344 async_read_timeout: ReadFile failed: timeout expired.
can't read packet header
../common/windows/async.c:344 async_read_timeout: ReadFile failed: timeout expired.
can't read packet header
../common/windows/async.c:344 async_read_timeout: ReadFile failed: timeout expired.
can't read packet header
../common/windows/async.c:344 async_read_timeout: ReadFile failed: timeout expired.
can't read packet header
../common/windows/async.c:344 async_read_timeout: ReadFile failed: timeout expired.
can't read packet header
../common/windows/async.c:344 async_read_timeout: ReadFile failed: timeout expired.
can't read packet header
../common/windows/async.c:344 async_read_timeout: ReadFile failed: timeout expired.
can't read packet header
../common/windows/async.c:344 async_read_timeout: ReadFile failed: timeout expired.
can't read packet header
../common/windows/async.c:344 async_read_timeout: ReadFile failed: timeout expired.
can't read packet header
after close the log and this appears:
cannot open file for writing:
C:\Users\Adrián\AppData\Roaming\gimx-launcher/output
cannot open file for writing:
C:\Users\Adrián\AppData\Roaming\gimx-launcher/outputChoice
cannot open file for writing:
C:\Users\Adrián\AppData\Roaming\gimx-launcher/input
cannot open file for writing:
C:\Users\Adrián\AppData\Roaming\gimx-launcher/inputChoice
Matlo wrote: ↑Fri Sep 15, 2017 5:39 am
Hi,
Please post a clear picture of the wiring and describe how you load the firmware.
ok, when i load the firmware this is the error.
I connect arduino Leonardo, open arduino builder versión 0.9.1. Load the firmware 5.8 EMUG29PS4 atmega32u4 and push COMX (i tried in different port USB COM4, COM5, COM6 and i have the same results). And then appears the error. And i tried also push button reset of board Leonardo when i push COM4.
First make sure the wiring between the cp210x and the Arduino Leonardo board is correct.
Then start gimx-loader and follow the instructions. The pro micro side equivalent is the Arduino Leonardo.
Matlo wrote: ↑Fri Sep 22, 2017 12:24 pm
First make sure the wiring between the cp210x and the Arduino Leonardo board is correct.
Then start gimx-loader and follow the instructions. The pro micro side equivalent is the Arduino Leonardo.
ummm.. this is the log when i load firmaware with gimx loader:
Connecting to programmer: .avrdude: butterfly_recv(): programmer is not responding
avrdude: butterfly_recv(): programmer is not responding
avrdude: butterfly_recv(): programmer is not responding
avrdude: butterfly_recv(): programmer is not responding
avrdude: butterfly_recv(): programmer is not responding
avrdude: butterfly_recv(): programmer is not responding
Found programmer: Id = ""; type =
Software Version = . ; Hardware Version = └.·
avrdude: butterfly_recv(): programmer is not responding
avrdude: butterfly_recv(): programmer is not responding
avrdude: error: buffered memory access not supported. Maybe it isn't
a butterfly/AVR109 but a AVR910 device?
avrdude: initialization failed, rc=-1
Double check connections and try again, or use -F to override
this check.
avrdude: butterfly_recv(): programmer is not responding
avrdude: error: programmer did not respond to command: leave prog mode